본문바로가기

산업다아라 로고산업다아라 메인

통합검색 폼
전체 카테고리

050안심번호는 구매문의 전화걸기문자발송이 가능합니다.

  • facebook 공유
  • Twitter 공유
  • kakaostory 공유
  • blog 공유
VARIAN
Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal
VARIAN
Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal
이전
  • Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal
  • Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal
다음

다아라몰 견적거래 가이드

1. 견적거래란?
판매 제품에 대해 구매사와 판매사간 거래에 최적화되어 쉽고 편리하게 이용하실 수 있는 서비스입니다.
2. 견적 거래 절차 안내

삼성케미칼

Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal

견적거래 제품

직접거래

  • 진공기계용 접착제(Vacuum Sealing) ⇒고급형
  • 최소 구매 수량 : 1
  • 주문 수량 단위 : 1
품번 선택
제품 선택 폼
제품 선택 테이블
제조사코드 형번코드 제품가격
0001 0001
견적거래

선택 초기화

제품이미지

VARIAN

Torr Seal Bond VARIAN 118g 토르실 진공용접착제 torrseal

facebook 공유
Twitter 공유
kakaostory 공유
blog 공유
제품정보


☞ 본제품의 디자인,사양은 제조사의 사정에 따라 달라질수 있습니다.



▶ 품 명 : 진공 에폭시 본드

TORR SEAL BOND (VARIAN,Inc.)

High Vacuum Sealing Kit


▶ 용 량 : A제(Resin) - 82g (백색)

B제(Hardener) - 36g (회색)


▶ 색 상 : 연회색


▶ 특 징

- 진공도 : 10-9 Torr

- 경화시간 : 25˚C ː 경화시작 : 1~2시간, 완전경화 : 72시간

(24시간 후에는 약 90%의 완전경화 특성에 도달)

60˚C ː 경화시작 : 30분, 완전경화 : 2시간

80˚C ː 완전경화 : 1시간

120˚C ː 완전경화 : 20~30분

- 고강도 수지 에폭시

- 아민 Gas가 발생하지 않아 어떤 진공장치에도 사용

- 수지계 에폭시 접착제로서 일반 접착제보다 조성밀도가 좋음

- 가스 발생없이 경화하며, 강력하게 접착하기 때문에 진공 장치에도

안심하고 사용


▶ 용 도

- 진공장비의 정비, 씰링, 접착에 용이하게 적용

- 서로 다른 소재의 접착

(유리, 금속 및 세라믹을 포함한 다양한 재료에 접착가능)

- 볼트나 리벳을 사용하지 못하는 공정에 적용


▶ 사용방법

손으로 혼합할 때는 파트 A(수지)와 파트 B(경화제)를 올바른

비율(20:8.6)로 혼합하고 색상과 일관성이 균일해질 때까지

완전히 혼합하십시오.

사용하기 직전에 접착제를 혼합하는 것이 좋습니다.

혼합하기 전에 개별 구성요소의 온도는 중요하지 않지만 실내 온도에

가까워야 합니다. 혼합하는 동안과 후에 열 축적 현상은 정상입니다.

발열반응 또는 과도한 열축적의 가능성을 줄이기 위해, 한번에 900그램

미만으로 섞으세요. 적은 양을 혼합하면 열 축적이 최소화됩니다.


▶ 주의사항

접착표면은 깨끗하고 건조하며 오염되지 않아야 합니다.

접착제를 도포한 후에는 접착된 부품이 취급 강도(25°C에서 3~4시간)가

때까지 접촉상태로 유지해야 합니다.

(참고-접착강도는 다른 접합 구성에 따라 달라질 수 있습니다.)

접착중에 움직일 가능성이 없다면 부품을 고정할 필요는 없습니다.

접착제가 경화되기 전에 작업영역 및 도포장비에서 과다한 접착제를

청소하세요. 변성알코올 및 많은 일반적인 산업용 용제는 경화 접착제를

제거하는 데 적합합니다.


▶ 경화 참고사항

에폭시 수지는 응고 또는 결정화되기 쉽습니다.

이 경우 튜브를 따뜻한 물(약 100°F(38°C)에 30분간 담그면 제품을

액체상태로 쉽게 되돌릴 수 있습니다. 사용하기 전에 모든 재료가

녹았는지 확인하십시오.

필요한 경우 부드럽게 다시 세척하십시오. 경화제와 혼합하기 전에

수지 구성요소를 실온으로 되돌리십시오.

이 예열 프로세스는 성능 또는 제품 특성에 영향을 미치지 않습니다.






Torr Seal® Low Vapor Pressure Epoxy

Torr Seal® epoxy is resin seals vacuum leaks. Torr Seal can be used

at pressures of 10-9torr.

Torr Seal can bond to a variety of materials including glass, metal

and ceramics.Directions for use


Mixing :

1.When mixing by hand, combine Part A(Resin) and Part B(Hardener)

in the correct ratio and mix thoroughly until the color and

consistency are uniform. Tube Kits have been designed so that

squeezing equal length beads of part A and part B will give the

proper ratio.

2. Mixing the adhesive just prior to use is recommended.

The temperature of the separate components prior to mixing is

not critical, but they should be close to room temperature.

3. Heat buildup during and after mixing is normal. To reduce the

likelihood of exothermic reaction or excessive heat buildup,

mix less than 900 grams at a time.

Mixing smaller amounts will minimize heat buildup.


Applying :

1. Bonding surfaces should be clean, dry, and free of contamination.

2. Once the adhesive is applied, the bonded parts should be held in

contact until the part has developed handling strength

(3 to 4 hours @ 25° C)

note : this can vary with different bond configurations. It is not

necessary to clamp the parts unless movement during cure is likely.


Cure :

1. Hardening time 1 to 2 hours @ 25° C. Can also be fully cured with

heat such as ; 2 hours at a maximum temperature of 60°C.

Complete cure is obtained after 72 hours @ 25° C.

2. After 24 hours, approximately 90% of full cure properties are

attained at room temperature.

3. This product can also be cured for 1 hour @ 80° C or 20 to 30

minutes @ 120°C.

4. Heat cures can be modified to achieve a desired degree of cure

from handling strength to full cure.


Clean up :

1. It is important to clean up excess adhesive from the work area and

application equipment before it hardens.

2. Denatured alcohol and many common industrial solvents are

suitable for removing uncured adhesive.


Note on hardeningEpoxy resins are prone to solidification or

crystallization.

If this occurs, the product can easily be returned to a liquid state by

immersing the tube in warm water, approximately 100° F (38° C ) for

30minutes. Ensure all material is melted prior to use; gently re-warm

if necessary. Allow the resin component to return to room temperature

prior to mixing with the hardener. This warming process will not affect

performance or product properties.



Specifications Table










월 ~ 금요일 오전 9시 ~ 오후 6시 까지

반품/교환
카테고리 내 다른제품
이전
다음
카테고리 내 다른제품 전체보기
판매사의 다른제품
이전
다음
판매사의 다른제품 전체보기
위로가기

판매사 정보

판매사 정보 table
상호 삼성케미칼
대표자 조성숙
주소 경기 부천시 중동로 185 (중동) .
연락처
이메일 sschem@samsungchem.kr
사업자번호 891-19-00387
닫기

다아라몰 견적거래 가이드

1. 견적거래란?
판매 제품에 대해 구매사와 판매사간 거래에 최적화되어 쉽고 편리하게 이용하실 수 있는 서비스입니다.
2. 견적 거래 절차 안내